Massey Ferguson 2720

The Massey Ferguson 2720 is a tractor produced by Massey Ferguson. It is equipped with a 353.8 ci 5.8 L engine. The listed engine power is Diesel (listed): 147 hp / 109.6 kW. Transmission: 16 forward and 12 reverse. Operating weight: 13514 lbs 6129 kg.

Engine Power

Diesel (listed): 147 hp / 109.6 kW

Fuel & Capacities

56.3 gal 213.1 L

Transmission

16 forward and 12 reverse

Operating Weight

13514 lbs 6129 kg

Overview

	1982 - 1985 2000 SeriesRow-Crop tractor 2000 Series Row-Crop tractor

Production
Manufacturer	Massey Ferguson
Row-Crop tractor

Massey Ferguson 2720 Engine
Perkins 5.8L 6-cyl diesel
Fuel tank	56.3 gal 213.1 L
Engine details ...

Massey Ferguson 2720 Transmission
16-speed two-speed power shift
Transmission details ...

Massey Ferguson 2720 Power
Engine	147 hp 109.6 kW

Mechanical
Four-wheel drive
Power steering
Hydraulic wet disc brakes
Cab standard.

Hydraulics
Pressure	2538 psi 175.0 bar
Pump flow	14.5 gpm 54.9 lpm

Tractor hitch
Rear Type	III/II
Rear lift	16,140 lbs 7321 kg

Power Take-off (PTO)
Rear PTO	independent
Rear PTO Type	540/1000 (1.375)
Engine RPM	540@1992
	1000@2090

Dimensions & Tires
Wheelbase	107.5 inches 273 cm
Weight	13514 lbs 6129 kg
Front tire	16.9-28
Rear tire	20.8-38
Full dimensions and tires ...

Electrical
Ground	negative
Battery volts	12

References

2720 published in 1982, by Massey Ferguson

Engine

Engine Detail — 353.8 ci / 5.8 L Diesel

Manufacturer	Perkins AT6.354.4
Configuration	turbocharged intercooled diesel, 6-cylinder, liquid-cooled
Displacement	353.8 ci 5.8 L
Bore/Stroke	3.875x5.00 inches 98 x 127 mm
Power	147 hp 109.6 kW
Fuel system	direct injection
Air cleaner	dry
Pre-heating	ether injection
Rated RPM	2400
Torque	363.6 lb-ft 493.0 Nm
Torque RPM	1600
Starter type	electric
Oil capacity	21.7 qts 20.5 L
Coolant capacity	28.5 qts 27.0 L

Transmission

Transmission — 16 forward and 12 reverse two-speed power shift

Type	two-speed power shift
Gears	16 forward and 12 reverse
Clutch	355mm dry disc
Oil capacity	93 qts 88.0 L
With 20.8/18-38 rear tires.

Dimensions

Massey Ferguson 2720 Tires
Standard tires (ag)	Front: 16.9-28. Rear: 20.8-38

Dimensions
Wheelbase	107.5 inches 273 cm
Length	200.4 inches 509 cm
Width	83.5 inches 212 cm
Height (cab)	112.2 inches 284 cm
Weight	13514 lbs 6129 kg

Photos

Massey Ferguson 2720

Recommended Implements & Sizing Guide

Engineering recommendations for Massey Ferguson 2720 based on its 147 HP power envelope and ASAE agricultural standards.

Implement & Operation	Recommended Size	Workload Rating	Engineering Notes
Moldboard PlowPrimary Tillage	5 to 7 Bottom (18")5 - 7 铧 (45 cm)	Commercial / Field Scale	Large acreage tillage; requires front ballast weights.
Rotary Cutter / MowerMowing & Clearing	10 to 12 ft Flex-Wing3.0 - 3.6 m 折叠双翼	Heavy Duty	Wide swath pasture and crop residue shredding.
Rotary TillerSeedbed Prep	90 to 120 in Heavy Duty230 - 300 cm 重型旋耕机	Commercial / Field Scale	Deep intensive seedbed preparation for commercial row crops.
Disc HarrowSecondary Tillage	15 to 22 ft Folding Disc4.5 - 6.7 m 折叠式圆盘耙	Commercial / Field Scale	Wide commercial field leveling; requires hydraulic remotes.
Hay BalerHay & Forage	5x6 Round Baler or 3x3 Mid Square1.5x1.8 m 大圆捆或中型方捆机	Heavy Duty	High density baling; requires minimum 85 PTO HP.

Sizing & Soil Condition NoteActual implement sizing varies depending on local soil conditions (heavy clay vs sandy loam), field slope, and operating speed. Heavy tillage implements may require front ballast weights and wheel weights.

Fluids, Capacities & Working Autonomy

Standard fluid requirements, service intervals, and continuous runtime estimates for Massey Ferguson 2720.

Estimated Continuous Field Runtime: 7.4 hrs

Approximately 7.4 hours of continuous field operation at ~75% rated power on a full tank (56.3 gal / 213.1 L).

Estimated 75% Load Fuel Burn~7.6 gal/hr (28.9 L/hr)

Engine Crankcase Oil

SAE 15W-40 (Heavy Duty Diesel)

Standard Spec: API CK-4 / CJ-4 Heavy Duty

Service Interval: 150 – 250 Hours

Transmission & Hydraulic System

UTTO (Universal Tractor Transmission Oil)

Standard Spec: ISO VG 46 / 68 (Wet Brake & Trans Compatible)

Service Interval: 600 – 1000 Hours

Engine Cooling System

50/50 Ethylene Glycol Pre-mix

Standard Spec: ASTM D6210 / Heavy-Duty OAT Antifreeze

Service Interval: 2 Years / 1500 Hours