Shibaura SF1040T

The Shibaura SF1040T is a tractor produced by Shibaura. It is equipped with a 278.3 ci 4.6 L engine. The listed engine power is Diesel (listed): 105 hp / 78.3 kW. Transmission: 16 forward and 4 reverse. Operating weight: 7915 lbs 3590 kg.

Engine Power

Diesel (listed): 105 hp / 78.3 kW

Fuel & Capacities

26.4 gal 99.9 L

Transmission

16 forward and 4 reverse

Operating Weight

7915 lbs 3590 kg

Overview

	SF SeriesUtility tractor
SF Series
Utility tractor

Production
Manufacturer	Shibaura
Utility tractor
Built in Matsumoto, Japan

Variants
SF1000T	2WD
SF1040T	4WD

Shibaura SF1040T Engine
Shibaura 4.6L 4-cyl diesel
Engine details ...

Shibaura SF1040T Transmission
16-speed constant mesh
Transmission details ...

Shibaura SF1040T Power
Engine	105 hp 78.3 kW
PTO (claimed)	96 hp 71.6 kW

Mechanical
Four-wheel drive
Power steering
Mechanical wet disc brakes
Open operator station. Two-post ROPS available.

Capacity
Fuel	26.4 gal 99.9 L
Hydraulic system	6.6 gal 25.0 L

Hydraulics
Type	open center
Capacity	6.6 gal 25.0 L
Pressure	2900 psi 200.0 bar
Pump flow	9.3 gpm 35.2 lpm

Tractor hitch
Rear Type	II
Control	position and draft control
Rear lift	5512 lbs 2500 kg

Power Take-off (PTO)
Rear PTO	independent
Rear PTO Type	540/800/1000

Dimensions & Tires
Weight	7915 lbs 3590 kg
Front tire	12.4-24
Rear tire	18.4-34
Full dimensions and tires ...

Electrical
Ground	negative
Charging system	alternator
Charging amps	30
Battery volts	12
Battery AH	170

References

SE5300 - SE6300 - SE7300T - SE8300 - SF1000T published in 1983, by Shibaura

Engine

Engine Detail — 278.3 ci / 4.6 L Diesel

Manufacturer	Shibaura LER1104T
Configuration	turbocharged diesel, 4-cylinder, liquid-cooled
Displacement	278.3 ci 4.6 L
Bore/Stroke	4.331x4.724 inches 110 x 120 mm
Power	105 hp 78.3 kW
Compression	17:1
Rated RPM	2200
Starter	electric
Starter volts	12

Transmission

Transmission — 16 forward and 4 reverse constant mesh

Type	constant mesh
Gears	16 forward and 4 reverse
Clutch	355mm dry disc
Four speeds, plus reverse, in four ranges.

Dimensions

Shibaura SF1040T Tires
Standard tires (ag)	Front: 12.4-24. Rear: 18.4-34

Dimensions
Length	161 inches 408 cm
Width	74 inches 187 cm
Height	108 inches 274 cm
Weight	7915 lbs 3590 kg

Photos

Shibaura SF1040T

Recommended Implements & Sizing Guide

Engineering recommendations for Shibaura SF1040T based on its 105 HP power envelope and ASAE agricultural standards.

Implement & Operation	Recommended Size	Workload Rating	Engineering Notes
Moldboard PlowPrimary Tillage	4 to 5 Bottom (16-18")4 - 5 铧 (40-45 cm)	Heavy Duty	Heavy primary tillage; semi-mounted hitch recommended.
Rotary Cutter / MowerMowing & Clearing	10 to 12 ft Flex-Wing3.0 - 3.6 m 折叠双翼	Heavy Duty	Wide swath pasture and crop residue shredding.
Rotary TillerSeedbed Prep	90 to 120 in Heavy Duty230 - 300 cm 重型旋耕机	Commercial / Field Scale	Deep intensive seedbed preparation for commercial row crops.
Disc HarrowSecondary Tillage	10 to 14 ft Tandem / Offset3.0 - 4.2 m 重型交错耙	Heavy Duty	Aggressive residue cutting in corn/cotton stubble.
Hay BalerHay & Forage	5x6 Round Baler or 3x3 Mid Square1.5x1.8 m 大圆捆或中型方捆机	Heavy Duty	High density baling; requires minimum 85 PTO HP.

Sizing & Soil Condition NoteActual implement sizing varies depending on local soil conditions (heavy clay vs sandy loam), field slope, and operating speed. Heavy tillage implements may require front ballast weights and wheel weights.

Fluids, Capacities & Working Autonomy

Standard fluid requirements, service intervals, and continuous runtime estimates for Shibaura SF1040T.

Estimated Continuous Field Runtime: 4.8 hrs

Approximately 4.8 hours of continuous field operation at ~75% rated power on a full tank (26.4 gal / 99.9 L).

Estimated 75% Load Fuel Burn~5.5 gal/hr (20.7 L/hr)

Engine Crankcase Oil

SAE 15W-40 (Heavy Duty Diesel)

Standard Spec: API CK-4 / CJ-4 Heavy Duty

Service Interval: 150 – 250 Hours

Transmission & Hydraulic System

UTTO (Universal Tractor Transmission Oil)

Standard Spec: ISO VG 46 / 68 (Wet Brake & Trans Compatible)

Service Interval: 600 – 1000 Hours

Engine Cooling System

50/50 Ethylene Glycol Pre-mix

Standard Spec: ASTM D6210 / Heavy-Duty OAT Antifreeze

Service Interval: 2 Years / 1500 Hours