New Holland TS110

The New Holland TS110 is a tractor produced by New Holland. It is equipped with a 304 ci 5.0 L engine. The listed engine power is Diesel (listed): 110 hp / 82.0 kW. Transmission: ElectroShift - creeper. Operating weight: 7308 to 10119 pounds.

Engine Power

Diesel (listed): 110 hp / 82.0 kW

Fuel & Capacities

42 gal 159.0 L

Transmission

ElectroShift - creeper

Operating Weight

7308 to 10119 pounds

Overview

	1999 - 2003 TS Series

Production
Manufacturer	New Holland
Built in Basildon, England

New Holland TS110 Engine
New Holland 5.0L 4-cyl diesel
Fuel tank	42 gal 159.0 L
Engine details ...

New Holland TS110 Power
Engine	110 hp 82.0 kW
PTO (claimed)	90 hp 67.1 kW

Mechanical
Two- or four-wheel drive
Power steering
Hydraulic wet disc brakes
Two-post folding ROPS. Cab optional with air-conditioning.

Hydraulics
Type	open center
	closed center OptOptional
Pressure	2500 psi 172.4 bar
	2700 psi (open center) 186.2 bar
Valves	2 to 4
Pump flow	9.3 gpm 35.2 lpm
	17.4 gpm (optional pump) 65.9 lpm
	20 gpm (closed center) 75.7 lpm
Steering flow	9.1 gpm 34.4 lpm
Steering press.	2100 psi (2WD) 144.8 bar
	2500 psi (4WD) 172.4 bar

Tractor hitch
Rear Type	II
Rear lift (at 24"/610mm)	4,200 lbs 1905 kg
	6,210 lbs (assist ram) 2816 kg
	8,240 lbs (two assist rams) 3737 kg
	8,598 lbs (two rams, Elec draft control) 3900 kg

Power Take-off (PTO)
Rear PTO	independent
Rear PTO Type	540/1000

Dimensions & Tires
2WD Wheelbase	92.1 inches 233 cm
4WD Wheelbase	93 inches 236 cm
Weight	7308 to 10119 pounds
Front tire	7.50-16
Rear tire	16.9-30
Full dimensions and tires ...

Electrical
Ground	negative
Charging system	alternator
Charging amps	55
	100 (cab)
Batteries	1
	2 *Second battery optional with cabin.
Battery CCA	800
Battery volts	12

References

Operator's Manual TS90 - TS100 - TS110: EconoShift (86562958) published in 1998
Operator's Manual TS90 - TS100 - TS110: Synchro Command and ElectroShift (86562959) published in 1998
TS90 TS100 TS110 TS115 Operator's Manual (86630281) published in 2001
North American Buyer's Guide published in 1997, by New Holland

Engine

Engine Detail — 304 ci / 5.0 L Diesel

Manufacturer	New Holland Genesis
Configuration	turbocharged diesel, 4-cylinder, liquid-cooled
Displacement	304 ci 5.0 L
Bore/Stroke	4.40x5.00 inches 112 x 127 mm
Power	110 hp 82.0 kW
Compression	17.5:1
Rated RPM	2070
Firing order	1-3-4-2
Starter volts	12
Coolant capacity	14.8 qts 14.0 L
	16.8 qts (cab) 15.9 L
Intake valve clearance	0.014-0.018 inches (cold) 0.356 mm
Exhaust valve clearance	0.017-0.021 inches (cold) 0.432 mm
Oil capacity	12 qts 11.4 L

Transmission

Transmission options
8-speed unsynchronized gear
16-speed two-speed power shift
12-speed
24-speed
16-speed

Transmission — EconoShift

Transmission	EconoShift
Type	unsynchronized gear
Gears	8 forward and 2 reverse
Four gears, plus reverse, in two ranges. Tractor must be stopped, and clutch used, before shifting gear or range. Optional creeper range.
With 16.9-34 rear tires.

Transmission — Econo Dual Command

Transmission	Econo Dual Command
Type	two-speed power shift
Gears	16 forward and 4 reverse
Same as EconoShift, with an additional under-speed power shift button on the dashboard. The direct/underspeed ranges may be shifted on the move without the clutch. Four gears, plus reverse, in two ranges. Tractor must be stopped, and clutch used, before shifting gear or range. Optional creeper range.
With 16.9-34 rear tires.

Transmission — Synchro Command

Transmission	Synchro Command
Gears	12 forward and reverse
Oil capacity	60 qts 56.8 L
Four gears provided in three ranges, plus a shuttle lever. Tractor may be shifted on the move, using the clutch, between gears, high or medium range, and forward-reverse shuttle. Tractor must be stopped to enter low range.
16.9-38 rear tires.

Transmission — Synchro Dual Command

Transmission	Synchro Dual Command
Gears	24 forward and reverse
Oil capacity	60 qts 56.8 L
Same as Synchro Command, with an additional under-speed power shift button on the gear lever. The direct/underspeed ranges may be shifted on the move without the clutch. A 'dump button' on the shuttle lever can be used for clutchless shifting between forward and reverse.
16.9-38 rear tires.

Transmission — ElectroShift

Transmission	ElectroShift
Gears	16 forward and reverse
Oil capacity	64 qts 60.6 L

Transmission — ElectroShift - creeper

Transmission	ElectroShift - creeper
Gears	24 forward and reverse
Additional range of creeper gears can be selected using the clutch with the range in low. Creeper engaged by a toggle switch.

Dimensions

New Holland TS110 Tires
Ag front	7.50-16
Ag rear	16.9-30

Dimensions
2WD Wheelbase	92.1 inches 233 cm
4WD Wheelbase	93 inches 236 cm
2WD Length	150.2 inches 381 cm
4WD Length	158.9 inches 403 cm
Width	79.2 inches (cab) 201 cm
	76.9 inches (tires only) 195 cm
Ground clearance	15.5 inches 39 cm

New Holland TS110 Weight
	7,308 lbs (2WD) 3314 kg
	8,322 lbs (4WD) 3774 kg
	8,708 lbs (2WD cab) 3949 kg
	10,119 lbs (4WD cab) 4589 kg

New Holland TS110 Height
ROPS	113.7 inches 288 cm
Cab	106.8 inches 271 cm
Exhaust	111.5 inches 283 cm

Photos

New Holland TS110 tractor.

Recommended Implements & Sizing Guide

Engineering recommendations for New Holland TS110 based on its 110 HP power envelope and ASAE agricultural standards.

Implement & Operation	Recommended Size	Workload Rating	Engineering Notes
Moldboard PlowPrimary Tillage	4 to 5 Bottom (16-18")4 - 5 铧 (40-45 cm)	Heavy Duty	Heavy primary tillage; semi-mounted hitch recommended.
Rotary Cutter / MowerMowing & Clearing	10 to 12 ft Flex-Wing3.0 - 3.6 m 折叠双翼	Heavy Duty	Wide swath pasture and crop residue shredding.
Rotary TillerSeedbed Prep	90 to 120 in Heavy Duty230 - 300 cm 重型旋耕机	Commercial / Field Scale	Deep intensive seedbed preparation for commercial row crops.
Disc HarrowSecondary Tillage	10 to 14 ft Tandem / Offset3.0 - 4.2 m 重型交错耙	Heavy Duty	Aggressive residue cutting in corn/cotton stubble.
Hay BalerHay & Forage	5x6 Round Baler or 3x3 Mid Square1.5x1.8 m 大圆捆或中型方捆机	Heavy Duty	High density baling; requires minimum 85 PTO HP.

Sizing & Soil Condition NoteActual implement sizing varies depending on local soil conditions (heavy clay vs sandy loam), field slope, and operating speed. Heavy tillage implements may require front ballast weights and wheel weights.

Fluids, Capacities & Working Autonomy

Standard fluid requirements, service intervals, and continuous runtime estimates for New Holland TS110.

Estimated Continuous Field Runtime: 7.3 hrs

Approximately 7.3 hours of continuous field operation at ~75% rated power on a full tank (42 gal / 159 L).

Estimated 75% Load Fuel Burn~5.7 gal/hr (21.7 L/hr)

Engine Crankcase Oil

SAE 15W-40 (Heavy Duty Diesel)

Standard Spec: API CK-4 / CJ-4 Heavy Duty

Service Interval: 150 – 250 Hours

Transmission & Hydraulic System

UTTO (Universal Tractor Transmission Oil)

Standard Spec: ISO VG 46 / 68 (Wet Brake & Trans Compatible)

Service Interval: 600 – 1000 Hours

Engine Cooling System

50/50 Ethylene Glycol Pre-mix

Standard Spec: ASTM D6210 / Heavy-Duty OAT Antifreeze

Service Interval: 2 Years / 1500 Hours